MCS接枝共聚物的结构和形态

将甲基丙烯酸甲酯（ＭＭＡ）、苯乙烯（Ｓ）在氯化聚乙烯（ＣＰＥ）存在下进行悬浮接枝共聚，获得ＭＣＳ树脂。本文着重考察了ＭＣＳ树脂的化学结构及胶粒形态。结果表明，确实发生了接枝共聚。ＣＰＥ用量、ＲＳＨ含量、引发剂浓度、反应温度、溶胀时间及聚合转化率对ＭＣＳ树脂的接枝率、接枝效率均有影响。ＭＣＳ树脂是接枝共聚物、ＭＭＡ／Ｓ共聚物与ＭＭＡ均聚物的混合物，橡胶相ＣＰＥ在ＭＣＳ树脂中的分散情况为“海岛结构”，     

PC／ABS合金的研制及其在汽车上的应用

对ＰＣ／ＡＢＳ合金开发和研制及其在汽车上的应用作了评述。介绍了上海杰事公司在该领域的进展。     

聚乙烯接枝改性及其与铝的粘结性

聚乙烯在过氧化二异丙苯存在下分别与丙烯酸，顺丁烯酸酐，顺丁烯二酸，顺丁烯二酸钠，丙烯酸羧丙酯，甲基丙烯酸环丙酯等单体熔融挤出，产物的红外光谱表明聚乙烯不同程度地接了各种极性基团。     

自洽场理论研究嵌段聚合物的并行算法实现

自洽场理论的数值计算方法在聚合物热力学的研究中得到了广泛的应用,尤其应用在嵌段共聚物微相分离形态的预测和描述方面[1～6]。该理论方法灵活性较强,参数空间的调整范围较大,能应用的计算体系也变化多样,难以建立固定的既有软件包,现有文献也鲜见针对该理论算法并行化的研究。本文就该理论在嵌段共聚物自组装问题上的数值计算的并行算法实现进行了研究和讨论,给出了算法性能的理论分析,并进行了实验测试。测试结果显示,本文提出的并行算法可获得良好的并行加速比,并行效率较高。该算法的提出有助于推动包括针对聚合物在内的软物质理论的研究工作。     

基于实验方法的硅胶圆管柔性关节静力学研究

采用两种不同材料的硅胶管和弹性骨架制作了柔性关节,对其进行静力学实验,得出了在相同气压下的弯曲角度和夹持力,并建立了柔性关节形变模型,获得了其气压下的形变特性。研究结果表明: 硅胶胶管邵氏硬度越小,其剪切弹性模量和弹性模量越小,其硅胶管制的柔性关节柔性和力学特性越好。该研究为弹性硅胶管在气动人工驱动器的应用进一步研究奠定了基础。     

丙烯酸酯橡胶耐有机溶剂及耐油性的研究

采用平衡溶胀法测定了日本瑞翁公司生产的活氯型丙烯酸酯橡胶(AR840)在24种不同有机溶剂中的溶胀行为,得到了AR840的一维溶解度参数值,其范围在18~23(MPa)^1/2之间。进一步用汉森三维溶解度参数软件(HSPiP)对溶胀数据进行分析研究,得到AR840三维溶解度参数值,色散分量(δ_d)、极性分量(δ_p)和氢键分量(δ_h)分别为18.20、8.70、3.60(MPa)^1/2。结果表明,AR840与24种溶剂存在着能量差(R_a),AR840与溶剂的溶胀比随着它们之间的Ra值的变化呈现反“S”型曲线,借助Ra的大小可以表征AR840在有机溶剂中的溶胀特性,能相对准确地表征丙烯酸酯橡胶(ACM)耐有机溶剂及耐油性能,对耐有机溶剂及耐油ACM的配方设计有一定的指导意义。     

Development of Covalent Chitosan-Polyethylenimine Derivatives as Gene Delivery Vehicle: Synthesis,Characterization, and Evaluation

There is an increasing interest in cationic polymers as important constituents of non-viral gene delivery vectors. In the present study, we developed a versatile synthetic route for the production of covalent polymeric conjugates consisting of water-soluble depolymerized chitosan (dCS; M_W 6–9 kDa) and low molecular weight polyethylenimine (PEI; 2.5 kDa linear, 1.8 kDa branched). dCS-PEI derivatives were evaluated based on their physicochemical properties, including purity, covalent bonding, solubility in aqueous media, ability for DNA condensation, and colloidal stability of the resulting polyplexes. They were complexed with non-integrating DNA vectors coding for reporter genes by simple admixing and assessed in vitro using liver-derived HuH-7 cells for their transfection efficiency and cytotoxicity. Using a rational screening cascade, a lead compound was selected (dCS-Suc-LPEI-14) displaying the best balance of biocompatibility, cytotoxicity, and transfection efficiency. Scale-up and in vivo evaluation in wild-type mice allowed for a direct comparison with a commercially available non-viral delivery vector (in vivo-jetPEI). Hepatic expression of the reporter gene luciferase resulted in liver-specific bioluminescence, upon intrabiliary infusion of the chitosan-based polyplexes, which exceeded the signal of the in vivo jetPEI reference formulation by a factor of 10. We conclude that the novel chitosan-derivative dCS-Suc-LPEI-14 shows promise and potential as an efficient polymeric conjugate for non-viral in vivo gene therapy.     

No Direct Postconditioning Effect of Poloxamer 188 on Mitochondrial Function after Ischemia Reperfusion Injury in Rat Isolated Hearts

Myocardial infarction is a leading cause for morbidity and mortality worldwide. The only viable treatment for the ischemic insult is timely reperfusion, which further exacerbates myocardial injury. Maintaining mitochondrial function is crucial in preserving cardiomyocyte function in ischemia reperfusion (IR) injury. Poloxamer (P) 188 has been shown to improve cardiac IR injury by improving cellular and mitochondrial function. The aim of this study was to show if P188 postconditioning has direct protective effects on mitochondrial function in the heart. Langendorff prepared rat hearts were subjected to IR injury ex-vivo and reperfused for 10 min with 1 mM P188 vs. vehicle. Cardiac mitochondria were isolated with 1 mM P188 vs. 1 mM polyethylene glycol (PEG) vs. vehicle by differential centrifugation. Mitochondrial function was assessed by adenosine triphosphate synthesis, oxygen consumption, and calcium retention capacity. Mitochondrial function decreased significantly after ischemia and showed mild improvement with reperfusion. P188 did not improve mitochondrial function in the ex-vivo heart, and neither further P188 nor PEG induced direct mitochondrial protection after IR injury in this model.     

Preparation of Iron Filler-Based Photocomposites and Application in 3D Printing

The introduction of metallic fillers to polymers via the photopolymerization approach can endow the composite materials with some unique properties, but the relevant research is still scarce due to the issue of light penetration and inner filter effect. Herein, for the first time the fabrication of photocomposites based on fine iron powder (i.e., a typical kind of metallic filler) is reported in this work. The free radical polymerization of two different acrylate monomers, poly(ethylene glycol) diacrylate and trimethylolpropane triacrylate, is performed in the presence of iron filler under mild conditions (i.e., light emitting diode (LED)@405 nm irradiation at room temperature under air). And the real-time Fourier transform infrared spectroscopy reveals remarkable photopolymerization kinetics of acrylates with high final conversions and fast polymerization rates despite the increasing contents of iron filler in the composites. Interestingly, the 3D printing technique is applied to the iron filler-based composites to produce tridimensional patterns with excellent spatial resolution. This work not only paves the way for the investigation of photocomposites based on metallic fillers through photochemical methods, but also broadens the potential application prospects.     

紫外光快速固化的树枝状丙烯酸酯齐聚物的制备和性能

通过乙二胺(EDA)和三羟甲基丙烷三丙烯酸酯(TMPTA)，以甲醇为催化剂，在30℃进行6小时Michael加成反应，可制得含多个双键的树枝状丙烯酸酯齐聚物(DAO)．与相似分子量的线性丙烯酸酯齐聚物相比，DAO粘度低，用作紫外光固化树脂，其固化速度快，且固化产物硬度好，耐溶剂性好．